Due to inclement weather in our area, order processing and carrier deliveries may be delayed. We sincerely appreciate your patience as we work through these disruptions to get your order to you as quickly as possible.

Engine - GM (19433063)

19433063

Engine - GM (19433063)

19433063

Buick, GMC, Cadillac, Hummer, Saturn, Oldsmobile, Pontiac, Chevrolet Parts
  • GM
  • 19433063
  • 12682080, 19370671, 19418256

Details

  • Brand:

    Buick, GMC, Cadillac, Hummer, Saturn, Oldsmobile, Pontiac, Chevrolet Parts

  • SKU:

    19433063

  • Description:

    E-ROD SYSTEMS HAVE IT ALL
    Each E-ROD crate engine system carries an official California Air Resources Board (CARB) E.O. number and includes complete emissions equipment, along with the engine controller and harness needed to get the engine running. The primary elements of each kit include:

    • Chevrolet Performance crate engine
    • Engine control module
    • Exhaust manifolds
    • Catalytic converters
    • Mass airflow sensor and sensor boss
    • Oxygen sensors and sensor bosses
    • Air filter
    • Accelerator pedal
    • Evaporative emissions canister
    • Instruction manual
    E-ROD LT1 6.2L SYSTEM
    • CARB EO#: (PENDING)
    • Horsepower: 455 @ 6,000 rpm
    • Torque: 465 lb.-ft. @ 4,600 rpm
    Introduced on the seventh-generation Corvette Stingray and Gen 6 Camaro SS, the LT1 6.2L V-8 opened the next chapter in the long, historic legacy of the Small-Block engine. It is architecturally similar to the LS family of Small-Block engines, but with a unique block casting, cylinder head design, oiling system and more. It also combines advanced technologies including direct injection and continuously variable valve timing to support an advanced combustion system. Chevrolet Performance's new LT1 crate engine - offered with a wet-sump or dry-sump oiling system - and a controller specially designed for retro-fit applications is included. This is the first LT-based E-Rod system and the most technically advanced. It is also available in a Connect & Cruise package with a matched 4L75-E automatic transmission.
    INSTALLATION NOTES
    Engines shipped with high-pressure direct-injection fuel pump installed
    Assembly does not include any electronics
    Kit includes electronic throttle pedal, which is required for throttle input to the ECU
    Intended for pre-1995 street vehicles or any off-road vehicle
    Not intended for marine applications
    Front-End Accessory Drive Kit can be ordered separately
    8-bolt crankshaft flange
    Shipped with 14" flexplate
    BUILDER'S NOTE
    To facilitate a complete E-ROD installation, the builder will need to source additional components to complete the assembly and get the vehicle running, including:
    • Fuel tank
    • Fuel lines (re-circulating or returnless)
    • Fuel pump - 58 psi (400 kPa) for LC9 and LS3 or 65 psi (450 kPa) for LSA
    • Fuel tank vent line from the tank to the evaporative emissions canister
    • Purge line from the canister to the engine purge solenoid
    • Air induction system that incorporates the mass airflow sensor
    • Exhaust system behind the catalytic converters.
    All E-ROD engines require a front-end accessory drive system suitable to the vehicle. The instruction manual included with each kit offers recommendations for the accessory drive kit, as well as the transmission, gear ratios and more. Chevrolet offers several configurations of accessory drive systems to suit different applications; and each allows the installer to easily delete air conditioning.
    Chevrolet Performance recommends the LS1 Engine Installation Guide P/N 88959384, which illustrates basic procedures and offers helpful tips on installing an LS engine into older vehicles.
    E-ROD systems do not come with a transmission. Chevrolet Performance recommends the SuperMatic(TM) 4L70-E - P/N 19244043 - four-speed automatic overdrive transmission, along with Chevrolet Performance's SuperMatic(TM) transmission controller P/N 19257634, for LC9 and LS3 systems. The LSA, with higher torque output, should use the SuperMatic(TM) 4L85-E, P/N 19300175, along with the SuperMatic(TM) transmission controller, P/N 19302410.
    *GM automatic transmissions are typically equipped with 40-tooth reluctor wheels for vehicle speed sensor output. GM late-model manual transmissions are typically equipped with a 17-tooth reluctor wheel. The Chevrolet Performance T56 Super Magnum six-speed manual (P/N 19329795) is equipped with a 40-tooth reluctor wheel.
    You May Also Like
    Bell Housing Kit LS and LT Engines
    $860.52
    Clutch Kit LS/LT Engines (8-Bolt Crank)
    $1,714.42
    LT1 Aluminum Automatic Bell Housing
    $176.90

  • Replaces:

    12682080, 19370671, 19418256

  • MSRP: $15,266.18
  • Discount: $2,462.98 (16.1% off)
  • Sale Price: $12,803.20
Manufacturer Warranty Minimum of 12 Months
Guaranteed Fitment Always the correct parts
Shop with Confidence Your information is safe
In-House Experts We know our products

Details

  • Brand:

    Buick, GMC, Cadillac, Hummer, Saturn, Oldsmobile, Pontiac, Chevrolet Parts

  • SKU:

    19433063

  • Description:

    E-ROD SYSTEMS HAVE IT ALL
    Each E-ROD crate engine system carries an official California Air Resources Board (CARB) E.O. number and includes complete emissions equipment, along with the engine controller and harness needed to get the engine running. The primary elements of each kit include:

    • Chevrolet Performance crate engine
    • Engine control module
    • Exhaust manifolds
    • Catalytic converters
    • Mass airflow sensor and sensor boss
    • Oxygen sensors and sensor bosses
    • Air filter
    • Accelerator pedal
    • Evaporative emissions canister
    • Instruction manual
    E-ROD LT1 6.2L SYSTEM
    • CARB EO#: (PENDING)
    • Horsepower: 455 @ 6,000 rpm
    • Torque: 465 lb.-ft. @ 4,600 rpm
    Introduced on the seventh-generation Corvette Stingray and Gen 6 Camaro SS, the LT1 6.2L V-8 opened the next chapter in the long, historic legacy of the Small-Block engine. It is architecturally similar to the LS family of Small-Block engines, but with a unique block casting, cylinder head design, oiling system and more. It also combines advanced technologies including direct injection and continuously variable valve timing to support an advanced combustion system. Chevrolet Performance's new LT1 crate engine - offered with a wet-sump or dry-sump oiling system - and a controller specially designed for retro-fit applications is included. This is the first LT-based E-Rod system and the most technically advanced. It is also available in a Connect & Cruise package with a matched 4L75-E automatic transmission.
    INSTALLATION NOTES
    Engines shipped with high-pressure direct-injection fuel pump installed
    Assembly does not include any electronics
    Kit includes electronic throttle pedal, which is required for throttle input to the ECU
    Intended for pre-1995 street vehicles or any off-road vehicle
    Not intended for marine applications
    Front-End Accessory Drive Kit can be ordered separately
    8-bolt crankshaft flange
    Shipped with 14" flexplate
    BUILDER'S NOTE
    To facilitate a complete E-ROD installation, the builder will need to source additional components to complete the assembly and get the vehicle running, including:
    • Fuel tank
    • Fuel lines (re-circulating or returnless)
    • Fuel pump - 58 psi (400 kPa) for LC9 and LS3 or 65 psi (450 kPa) for LSA
    • Fuel tank vent line from the tank to the evaporative emissions canister
    • Purge line from the canister to the engine purge solenoid
    • Air induction system that incorporates the mass airflow sensor
    • Exhaust system behind the catalytic converters.
    All E-ROD engines require a front-end accessory drive system suitable to the vehicle. The instruction manual included with each kit offers recommendations for the accessory drive kit, as well as the transmission, gear ratios and more. Chevrolet offers several configurations of accessory drive systems to suit different applications; and each allows the installer to easily delete air conditioning.
    Chevrolet Performance recommends the LS1 Engine Installation Guide P/N 88959384, which illustrates basic procedures and offers helpful tips on installing an LS engine into older vehicles.
    E-ROD systems do not come with a transmission. Chevrolet Performance recommends the SuperMatic(TM) 4L70-E - P/N 19244043 - four-speed automatic overdrive transmission, along with Chevrolet Performance's SuperMatic(TM) transmission controller P/N 19257634, for LC9 and LS3 systems. The LSA, with higher torque output, should use the SuperMatic(TM) 4L85-E, P/N 19300175, along with the SuperMatic(TM) transmission controller, P/N 19302410.
    *GM automatic transmissions are typically equipped with 40-tooth reluctor wheels for vehicle speed sensor output. GM late-model manual transmissions are typically equipped with a 17-tooth reluctor wheel. The Chevrolet Performance T56 Super Magnum six-speed manual (P/N 19329795) is equipped with a 40-tooth reluctor wheel.
    You May Also Like
    Bell Housing Kit LS and LT Engines
    $860.52
    Clutch Kit LS/LT Engines (8-Bolt Crank)
    $1,714.42
    LT1 Aluminum Automatic Bell Housing
    $176.90

  • Replaces:

    12682080, 19370671, 19418256

Buick, GMC, Cadillac, Hummer, Saturn, Oldsmobile, Pontiac, Chevrolet Parts
  • GM
  • 19433063
  • 12682080, 19370671, 19418256

Vehicle Fitment

No application/vehicle fitment information available for this product

Details

  • Brand:

    Buick, GMC, Cadillac, Hummer, Saturn, Oldsmobile, Pontiac, Chevrolet Parts

  • SKU:

    19433063

  • Description:

    E-ROD SYSTEMS HAVE IT ALL
    Each E-ROD crate engine system carries an official California Air Resources Board (CARB) E.O. number and includes complete emissions equipment, along with the engine controller and harness needed to get the engine running. The primary elements of each kit include:

    • Chevrolet Performance crate engine
    • Engine control module
    • Exhaust manifolds
    • Catalytic converters
    • Mass airflow sensor and sensor boss
    • Oxygen sensors and sensor bosses
    • Air filter
    • Accelerator pedal
    • Evaporative emissions canister
    • Instruction manual
    E-ROD LT1 6.2L SYSTEM
    • CARB EO#: (PENDING)
    • Horsepower: 455 @ 6,000 rpm
    • Torque: 465 lb.-ft. @ 4,600 rpm
    Introduced on the seventh-generation Corvette Stingray and Gen 6 Camaro SS, the LT1 6.2L V-8 opened the next chapter in the long, historic legacy of the Small-Block engine. It is architecturally similar to the LS family of Small-Block engines, but with a unique block casting, cylinder head design, oiling system and more. It also combines advanced technologies including direct injection and continuously variable valve timing to support an advanced combustion system. Chevrolet Performance's new LT1 crate engine - offered with a wet-sump or dry-sump oiling system - and a controller specially designed for retro-fit applications is included. This is the first LT-based E-Rod system and the most technically advanced. It is also available in a Connect & Cruise package with a matched 4L75-E automatic transmission.
    INSTALLATION NOTES
    Engines shipped with high-pressure direct-injection fuel pump installed
    Assembly does not include any electronics
    Kit includes electronic throttle pedal, which is required for throttle input to the ECU
    Intended for pre-1995 street vehicles or any off-road vehicle
    Not intended for marine applications
    Front-End Accessory Drive Kit can be ordered separately
    8-bolt crankshaft flange
    Shipped with 14" flexplate
    BUILDER'S NOTE
    To facilitate a complete E-ROD installation, the builder will need to source additional components to complete the assembly and get the vehicle running, including:
    • Fuel tank
    • Fuel lines (re-circulating or returnless)
    • Fuel pump - 58 psi (400 kPa) for LC9 and LS3 or 65 psi (450 kPa) for LSA
    • Fuel tank vent line from the tank to the evaporative emissions canister
    • Purge line from the canister to the engine purge solenoid
    • Air induction system that incorporates the mass airflow sensor
    • Exhaust system behind the catalytic converters.
    All E-ROD engines require a front-end accessory drive system suitable to the vehicle. The instruction manual included with each kit offers recommendations for the accessory drive kit, as well as the transmission, gear ratios and more. Chevrolet offers several configurations of accessory drive systems to suit different applications; and each allows the installer to easily delete air conditioning.
    Chevrolet Performance recommends the LS1 Engine Installation Guide P/N 88959384, which illustrates basic procedures and offers helpful tips on installing an LS engine into older vehicles.
    E-ROD systems do not come with a transmission. Chevrolet Performance recommends the SuperMatic(TM) 4L70-E - P/N 19244043 - four-speed automatic overdrive transmission, along with Chevrolet Performance's SuperMatic(TM) transmission controller P/N 19257634, for LC9 and LS3 systems. The LSA, with higher torque output, should use the SuperMatic(TM) 4L85-E, P/N 19300175, along with the SuperMatic(TM) transmission controller, P/N 19302410.
    *GM automatic transmissions are typically equipped with 40-tooth reluctor wheels for vehicle speed sensor output. GM late-model manual transmissions are typically equipped with a 17-tooth reluctor wheel. The Chevrolet Performance T56 Super Magnum six-speed manual (P/N 19329795) is equipped with a 40-tooth reluctor wheel.
    You May Also Like
    Bell Housing Kit LS and LT Engines
    $860.52
    Clutch Kit LS/LT Engines (8-Bolt Crank)
    $1,714.42
    LT1 Aluminum Automatic Bell Housing
    $176.90

  • Replaces:

    12682080, 19370671, 19418256

Manufacturer Warranty Minimum of 12 Months
Guaranteed Fitment Always the correct parts
Shop with Confidence Your information is safe
In-House Experts We know our products

GM Wholesale Direct

Personalize, customize, and accessorize with GM Wholesale Direct. With one of the largest genuine GM parts and accessory inventories in the country, you are sure to get the item you need quickly at wholesale or better prices! Order your Engine (19433063) right here on the site and have it at your door in just a matter of days Your Engine will be a genuine part that will perfectly fit your vehicle. 

Don't see something on the page you need? Feel free to contact us and we will build a custom order just for you. Our dedicated online parts associates are ready to help. Phone: 855-578-2622 Email: [email protected]

You can shop from model specific OEM part catalogs as well. Just select what make you want to shop for from the list below to get started:

| Buick Models | Cadillac Models | Chevrolet Models | GMC Models |

| Hummer Models | Oldsmobile Models | Pontiac Models | Saturn Models |